VK3MRG   Amateur Radio
  • Blog
  • About
  • Equipment

Yet another Antenna for 2 Metres

22/2/2014

3 Comments

 
Over the past year I've activated a few SOTA summits with nothing more than a handheld and the stock antenna supplied. I have also looked at a couple of options to improve performance and keep weight and bulk down to a minimum.

The first thing I tried was a pigtail wire. This is simply a ¼ wave length of wire with a lug at one end that simply screws down on the SMA connector between the antenna and the radio and acts as a counterpoise for improved performance. Playing around with one of these does make a marginal difference and might be enough to get the contact logged where you would otherwise fail.

One of the other things I've tried is to unscrew the ground independent dual band whip from the vehicle take it to the summit sticking out of the backpack. A 5 metre length of coax with a BNC and base socket for the antenna is the connecttion for the radio and are the main parts of this setup. At the transmitting site, a string can be tied to the tip of the antenna and thrown over a tree limb to hoist it up a few metres. The antenna can also be taped to a squid pole or other support. This setup is versatile and light and takes up the least amount of room and is ideal for HT only activations with the only disadvantage being the length of the whip sticking out of the backpack being a nuisance when traversing through thick bush. A setup like this will almost certainly allow you to qualify summits within striking range of urban areas quickly without the need to mess around setting up radios, batteries and bulky antennas for other bands.

I've also tried a 2 metre J-pole antenna made from 300 ohm TV ribbon which is wonderfully light and compact but the biggest problem has been reliability. The wire is so fine that it it quickly breaks usually at the most inconvenient time.

  Something that caught my eye recently was the SOTABEAMS 2 metre MFD ( Multi Function Dipole). I like the idea of a complete self supporting antenna such as the vertical HF antenna I frequently use on SOTA activations as it packs completely within the backpack without the need for an additional tuner or bulky squid pole. The MFD promises reasonable performance with the flexibility to mount the dipole section vertically for FM or horizontally for SSB operation. To buy the kit from SOTABEAMS in the UK would cost around $55 with the optional goody bag consisting of some nylon rope, 3 ground pegs and a couple of velcro straps. Another option is a ground spike at an additional cost. Fair enough but looking at pictures and a youtube video of the antenna, I decided that I would build one myself as I had all the other ingredients except the 20mm electrical conduit, T-connector and couplings.

Picture
The MRG MFD with the pole sections and spike
Picture

A quick trip down to Bunnings and a short time later I had a 4 metre length of conduit and the other bits for under $5.

The ingredients for MRG MFD antenna as constructed:
3.5 metres RG58/U
1 x BNC connector
1030mm insulated copper strand wire
1 x twin terminal block
1 x small cable tie
4 x 510mm lengths 20mm pvc conduit
1 x 110mm length 20mm pvc conduit
2 x 20mm conduit couplings
1 x 20mm T-connector with inspection cover

Optional parts to complete the antenna:
3 x 2.5m nylon rope
3 x tent pegs

A ground spike of some description is worthwhile. I happened to have an unused aluminium spike from a low voltage garden light which the conduit screwed into perfectly. The spike also has a cover made from an offcut of conduit to protect the spike from damaging anything in transit.


Picture
Putting the antenna together is simple enough. Cut the conduit lengths as described. The wire I used for the dipole was striped out of an old extension cord. Cut the 1030mm wire into 2 x ¼ wavelengths for the dipole. These will be trimmed to SWR later. Strip the insulation on one end of the wires and screw into the terminal connector. Push the 110mm conduit firmly into the bottom of the T-connector and carefully drill a hole and feed the RG58/U into the connector. Strip back the coax and terminate the braid to one side of the terminal block and the centre lead to the other. Get your glue gun and melt a big blob of glue onto the back of the terminal block and quickly position it centrally inside the T-connector before it sets. Gently pulling the coax back through the drilled hole will help position the terminal block before the glue sets. Feed the dipole wires out each side of the T-connector and then tightly wrap 15 turns of the coax around the conduit to form a choke balun. Drill 2 small holes in the conduit adjacent to the last turn of coax and install the cable tie to hold the choke balun in place. Terminate the end of the coax with a BNC or other connector to suit your radio. The choke balun consumes almost one metre of the coax and the remaining 2.5 metres or so is ample for most portable setups.

Picture
A spike from a low voltage garden light fits perfectly
Picture
Feed one side of the dipole wire back through the centre for storage or transporting
  Next assemble the antenna. Erect the two lower pole sections using the couplings and either strap it to a vertical support or spike it like mine. There should be at least 10mm of conduit at the end of your choke balun to push into the vertical section. Feed the dipole wires through the other two conduit sections and push into the T-connector. Congratulations. You now have a horizontal dipole for 2 metres. The next thing to do is SWR the antenna. I tuned my antenna for the middle of the band at 146.000 Mhz. The easiest way to cut the dipole is to pull the dipole tubes out and cut the wires together side by side. Reassemble the supporting tubes and test the SWR again. Continue as many times as required to tune the antenna but take it easy. Cut no more than 2mm at a time when the SWR gets down around 1:5 to 1 or you may take too much off.

Picture
Once tuned, a quck test with the multimeter just to detemine which leg of the dipole is connected to the centre of the coax. Mark an arrow in the T-connector so when the antenna is used vertically, this side of the dipole will be at the top. When disassembled the conduit in the “hot” side of the antenna is pulled apart and the wire is simply fed back through the T-connector for storage. Be sure to leave a little loop near the end so it can easily be pulled out when assembling the antenna.

To test the antenna in field conditions I went down to the local park. I first set it up vertically. It was a reasonably windy afternoon and the antenna waved around a fair bit so I guyed it out with three lengths of light nylon rope with a loop in each end. With the antenna steadied I checked the SWR once again which hadn't changed from the initial tuning at all. I set up the FT-817 and tested out the antenna on a number of repeaters and was easily able to hit all of them that I could normaly do with a handheld. Next I put out a call on 146.500 FM and straight away got a response from Tony VK3CAT at his QTH, a distance of around 17 km. Not too bad with 5 watts across the suburbs.


Picture
The antenna guyed in vertical position
Picture
The antenna set up in horizontal position
  The next test was to set up the antenna horizontally and try SSB. It only took a minute to configure the antenna set up roughly broadside to Tony's position. This time I didn't really need to guy it despite the wind. Even though the antenna was little more than a metre parallel to the ground I received a good report once again from Tony and we also experimented moving the antenna end on where my signal remained perfectly readable despite dropping 2 or 3 S points. No real match for a 5 element yagi mounted a couple of metres higher but good enough for a SOTA peak without too much extra weight to lug around. It should prove to be a fairly reliable and robust antenna.

The packed down size is still a little bulky for a small backpack but manageable.

3 Comments

Sugarloaf Peak Revisited

15/2/2014

0 Comments

 
Picture
Sugarloaf Peak VK3/VN-011

Activated 15 February 2014

This activation was almost a repeat of my last activation of this summit back on 25 May 2013. It was planned at the last minute and once again I was accompanied by my two daughters who enjoyed the climb last time and were happy to come along.

Light rain started falling just as we arrived at the saddle carpark but it looked like it was going to blow over fairly quickly so we pressed on and started up Canyon Track. The rain made some of the rocky parts of the track slippery and extra care was needed. As we climbed the rain cleared and we were able to set up in the same position as last time. I spiked the vertical antenna into the ground and tapped the coil for 40 metres while the girls were running out the counterpoise wires.

I wanted to make this a fairly quick activation and keep any boredom at bay for the girls as Dad did his radio thing. This turned out well as I was quicly able to log my first contact with Ivan VK5HS at 0417z. Phil VK3BHR was next and was able to spot me on SOTAWATCH. From here on was a flow of contacts with Peter VK3FPSR, Peter VK3PF, Amanda VK3FQSO, Paul VK5PAS, Matt VK1MA. My last contact was with Joe VK3YSP operating portable in the Dandenong Ranges National Park as the rain returned. After 12 minutes on air and the summit easily qualified, we quickly packed the station away and made our way back down.

Thanks to the stations contacted allowing me to work you all efficiently as the weather rushed the activation to an abrupt end.



0 Comments

    Author

    Marshall  VK3MRG.
    Someone who likes to mix outdoor activities with radios at every opportunity.

    Blog Roll

    VK1DA
    VK1DI
    VK1NAM
    VK2DAG
    VK2FPJR
    VK2IB
    VK2JI

    VK2IO
    VK2LAX
    VK3BQ
    VK3IL
    VK3PF
    VK3YY
    VK3ARR
    VK3BYD
    VK3HRA
    VK3KAB
    VK3WAM
    VK3ZPF
    VK5LA
    VK5AKH
    VK5PAS
    VK7TW

    Archives

    December 2014
    September 2014
    August 2014
    July 2014
    June 2014
    May 2014
    April 2014
    March 2014
    February 2014
    January 2014
    December 2013
    November 2013
    October 2013
    September 2013
    August 2013
    July 2013
    June 2013
    May 2013
    April 2013

    Categories

    All
    Bicycle Hf Portable
    Pedestrian Hf Portable
    Portable Antennas
    Sota


Powered by Create your own unique website with customizable templates.